Raypak Temp-Tracker Especificações descarregar pdf (Página 20)

20 Raypak, Inc.

HTC# 059105-00D





To be able to change the TempTracker mod+ Hybrid settings the Program/Run Switch must be

set to Program. The switch is located under the Enclosure Wiring Cover for security.

SYSTEM

RUNPROGRAM

DO NOT APPLY ANY VOLTAGE

TO INPUT TERMINALS

RS-485

GND

VLT

SYS

PWR

CUR / VLT

GND

VLT

GND

VLT

GND

VLT

TEMP

OUTDOOR

TEMP

SYSTEM

EXTENSION

MODULE

CUR / VLT

PROVE

/DHW

SHUTDOWN

/SETBACK

FOR ALL CIRCUITS

120VAC, 6A RESISTIVE

OUTPUT RATINGS:

1A PILOT DUTY, 15A TOTAL

115VAC 60Hz , 30VA MAX

INPUT RATINGS:

USE COPPER WIRE,

CLASS 1 WIRE ONLY.

CAUTION: RISK OF ELECTRIC SHOCK

More than one disconnect switch may be required

to de-energize the equipment before servicing.

ENCLOSED

ENERGY

MANAGEMENT

EQUIPMENT

99RA

/TSTAT

HYBRID



Button: MENU/<System Startup>

• When powered, the TempTracker mod+ Hybrid performs a self diagnostics-test.

• On the rst power up, the System Startup screen will appear after the initialization is

complete. If it doesn’t, the TempTracker mod+ Hybrid has already been congured.

• The System Startup menu sets the main parameters that relate to the heating application.

These settings must be set by the installer.

--------SETTINGS----

Season Winter

SystemTarget140

<SystemSettings>

<Maintenance>

<Histories>

<SystemStartup>

BACK▲▼SELECT



Modulation,Staging,Hybrid Default:Modulation

Button: MENU/<System Startup>/..../Boiler Type

• The same Raypak control can operate modulating boilers, staging boilers, or a combination

of both types.

• The Modulation option will operate a variety of modulating boilers.

• The Staging option will operate a variety of On/Off or multi-stage boilers.

• The Hybrid option will sequence two groups of boilers, condensing and non-condensing.

Each group could be of a different boiler type (Modulation or Staging). See "HYBRID

Startup Settings" on page 21. Each Multi-Stage boiler will use a single output relay. The

staging will take place using the voltage output signal.

• If BACnet is to be used, each of the Boiler Type modes will have a different set of BACnet

variables. See "Hybrid - Outdoor Reset - BACnet Variable list" on page 44..

---BOILERTYPE---

Modulation

Staging

Hybrid

BACK▲▼SAVE



Reset°F,Reset°C,SetPoint°F,SetPoint°C,4-20mAEMS Default:Reset°F

(Set Point Options Not Available with Hybrid Boiler Type)

Button: MENU/<System Startup>/..../Sensor Type

• If Reset °F is selected, all temperatures and settings will be displayed in degrees Fahrenheit

and the control will use Reset Ratios to adjust the system set point.

• If Reset °C is selected, all temperatures and settings will be displayed in degrees Celsius and

the control will use Reset Ratios to adjust the system set point.

• If Set Point °F is selected, all temperatures and settings will be displayed in degrees

Fahrenheit and the control will have an adjustable system set point.

• If Set Point °F is selected, all temperatures and settings will be displayed in degrees Celsius

and the control will have an adjustable system set point.

• The 4-20mA EMS option is only available to the Hybrid Boiler Type option. To use

4-20mA EMS with Staging and Modulating Boiler Types, select one of the Set Point options

and the EMS Input Mode menu will follow to offer the 4-20mA EMS option.

• The use of the 4-20mA EMS option requires the purchase of the 4-20mA EMS Interface

(#012019). It gives the TempTracker mod+ Hybrid the capability of accepting a remote

4-20mA signal from a BMS or EMS system as the target set point.

• If BACnet is to be used, each of the Sensor Type modes will have a different set of BACnet

variables. See "Hybrid - Outdoor Reset - BACnet Variable list" on page 44..

--SENSORTYPE--

Reset

Reset

SetPoint

BACK▲▼SAVE

---SENSORTYPE---

Reset

Reset

4-20mAEMS

BACK▲▼SAVE



Disable,Enable Default:Disable

(Available after Set Point with Staging or Modulation Boiler Types)

Button: MENU/<System Startup>/..../Boiler Type/Sensor Type / EMS Input Mode

• It allows the TempTracker mod+ Hybrid to utilize the 4-20mA EMS Interface (#012019) to

accept a remote 4-20mA signal from a BMS or EMS system as the target set point.

-EMSINPUTMODE-

Disable

Enable

BACK▲▼SAVE

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 55 56

Comentários a estes Manuais

Sem comentários

Raypak Temp-Tracker Especificações Página 20

Comentários a estes Manuais